PDA

View Full Version : FS: [AUS] Mazdaspeed Seat Brackets for BA, BG and NA/NB


Rupewrecht
07-07-2010, 02:07 PM
Mazdaspeed seats will fit in any car, but the seats themselves have an integral rail that cannot be removed, unlike most aftermarket seats.
This means they require a set of adapter brackets that mount to the corner of the integral rail for each different car.

These brackets are quite hard to find for most models, and are unavailable new from Mazda/Mazdaspeed for anything pre-2005.

So, i'm looking at getting drivers and passenger brackets replicated for:
- CBA Lantis / BA Astina / 323F
- BG Astina / BG Familia + Protege 3DR Hatch and BG Sedan (not 4WD) / Eunos 30X / Mazda MX-3 / Mazda Presso / Autozam AZ-3 / Eunos 100
- NA/NB MX-5 / Miata / Eunos Roadster
- No BJ ones at this stage, as i'd have to find them on the auctions and i don't think i've ever seen a set!

This will give anyone looking at the seats a much easier time to fit them - it's just a few simple bolts.

Projected cost is $85 per seat.

Ideally, i'd need 5-10 firm orders of each to make it worthwhile, and to cushion some of the $800+ outlay for each type.

But honestly, i'd be happy to sell a set of brackets with a seat for a decent amount less, just to sell a seat.

Interest?

Rupewrecht
12-07-2010, 06:26 PM
Here's a pic of the bottom of a Mazdaspeed seat, showing the integral rail. I've had a good look at the rail and it's part of the seat - to remove it would make the seat collapse!

http://rupewrecht.com/forsale/fs_ms_seatbasemeasurements.jpg

Rupewrecht
12-07-2010, 09:15 PM
After getting a couple of questions about this, these brackets bolt to the seat, and then bolt to the floor.

The large holes are the the ones that bolt to the floor, and the 2 set of small holes bolt to the studs on each corner of the rail on the Mazdaspeed seat base.

There is no need for anything else to fit a Mazdaspeed seat to your car, apart from a set of these brackets.

http://rupewrecht.com/forsale/fs_ms_mx5seatbrackets3.jpg

project.r.racing
13-07-2010, 06:49 PM
keen.
i'd also assume alot of mx5 boys would be also

koan123
25-07-2010, 07:35 AM
I've been directed here from MX5nutz, and I'd happily take a set of these!

70NYD
25-07-2010, 10:33 AM
im keen also as u already know :)

Ghoru
12-09-2010, 06:47 AM
i take it these never eventuated at all?

Rupewrecht
12-09-2010, 01:20 PM
They will, but when i have to find $1700 per car to get them made it's going to take a little while.

phly
15-09-2010, 10:22 AM
+1 BA Astina passenger bracket for me.

Got the Mazdaspeed Sport seat for the drivers side at the moment and need these brackets to put in the passenger side seat LOL. Pretty good seats compared to the standard series 3 ones.

Ghoru
15-09-2010, 07:07 PM
i will take 2 sets of bg ones please

Rupewrecht
15-10-2010, 09:54 AM
Just a heads-up - both drivers and passenger seat brackets for BA Astina are being made in the next 2 weeks, so please indicate your interest to make sure you don't miss out! Limited stocks.

Rupewrecht
16-12-2010, 03:05 PM
Just a heads-up - both drivers and passenger seat brackets for BA Astina are being made in the next 2 weeks, so please indicate your interest to make sure you don't miss out! Limited stocks.

...and now in stock, just in time for Christmas! More details to follow.

Buzz_LightYear
16-12-2010, 03:15 PM
...and now in stock, just in time for Christmas! More details to follow.

WWWHHOOOOOO.... :rolleyes:

Rupewrecht
16-12-2010, 07:49 PM
Now in stock:

Mazdaspeed seat brackets for:

1994-1998 323 BA Astina / CBA Lantis / BA 323F.
1994-1998 323 BH Protegé / BHA Familia / BA Protegé (2WD only)

- Drivers side and Passenger side available.
- Fits both Hatch/Coupé and Hardtop/Sedan.
- Works with Mazdaspeed Type-F, Type-T and Sports seats.
- Available in pairs (LHS and RHS) or individual sides.
- 8 sets available only (and probably no more after this!).

Price:
- $110 per individual seat (LHS or RHS)
- $210 for a pair (RHS and LHS)

Shipping:
- Australia: $15 for either a single or pair of brackets, Australia-wide.
- International: Please PM for a quote.

The brackets:

http://rupewrecht.com/forsale/fs_ms_lantis_seatbrackets_repro2.jpg

http://rupewrecht.com/forsale/fs_ms_lantis_seatbrackets_repro2.jpg

A.E
03-06-2011, 10:22 PM
Have you spotted a set on the auctions for BJ yet??

Rupewrecht
04-06-2011, 07:42 AM
Have you spotted a set on the auctions for BJ yet??

They don't exist for BJ - they were never made by Mazdaspeed.

scott b
05-06-2011, 08:56 PM
that doesnt mean we cant make AGT ones :P

Rupewrecht
24-06-2011, 10:02 AM
OK, prototypes are currently being made for NA/NB MX-5, thanks to Scott B / SJB Engineering (scott@sjbengineering.com.au) :)

Both Drivers/RHS and LHS/Passenger brackets will be made. Please indicate your interest! Projected cost is around $98 per side, or $190 for a set of both sides.

Born_Disturbed
07-07-2011, 03:42 PM
Hey rupe, i would need 2 out of the 4 NA P/S mounts as i have the other 2, also any chance of some BG 4WD mounts? fair bit of intrest this side of things if its possible

Rupewrecht
07-07-2011, 03:48 PM
Hey rupe, i would need 2 out of the 4 NA P/S mounts as i have the other 2, also any chance of some BG 4WD mounts? fair bit of intrest this side of things if its possible

You'd have to buy a passenger side set, as otherwise i'm left with 2 useless ones ;)

As for BG, i've got a set of BG FWD ones that might be done one day, but i don't know if there's really demand for them. I've never seen any for BG 4WD, so they'd have to be mocked up/CADed and made - but it's possible. Would really need some firm interest for either of the BG ones though.

Born_Disturbed
07-07-2011, 08:55 PM
Cant you just tell them to make half of one set? lol, i would have thought the 4WD ones would be more common. Should be able to get at elast 5 people over here intrested for both sets

curtklze
01-03-2012, 05:28 AM
I am interested in 2 or 3 sets (left and right side) of brackets for the mx3/30x,
are they the same as the astina ones?

thanks.

Rupewrecht
01-03-2012, 09:34 AM
I am interested in 2 or 3 sets (left and right side) of brackets for the mx3/30x,
are they the same as the astina ones?

thanks.

At the moment i haven't reproduced the BG Astina/MX-3 ones due to low demand. This may change in the future though.

Drift Thorpey
01-03-2012, 11:54 AM
Rupe I'm keen to get my hands on an MS bracket for a BG astina (possibly 2 depending on price)
can I be kept in the loop if these do come into circulation?
Cheers bud

Rupewrecht
01-03-2012, 01:08 PM
Sure, just subscribe to this thread.

Mooneggs
01-03-2012, 03:11 PM
I would also be interested in another set of mx-3 ones :D

Fosgate
04-03-2012, 11:58 PM
What about standard BG GTR seats in good condition... do you get any?

Rupewrecht
05-03-2012, 08:36 AM
What about standard BG GTR seats in good condition... do you get any?

Can't say i every really see them outside of a car, and not the sort of thing i'd bring in anyway really. But i'll post them up if i see any.

Rupewrecht
21-05-2012, 09:08 PM
Coming later this week - brackets for NA and NB MX-5!

Passenger and drivers side available. Limited stocks though, so get in quick!

memphis9787
26-05-2012, 01:25 PM
Hey Rupe Keen on some Eunos Brackets, although last time I tried putting Aussie Delivered Eunos 30x seats in my car it didn't fit as the rail width was too wide to bolt into my floor , so not really sure which Brackets I'd need.

chewyryce
26-05-2012, 07:56 PM
Coming later this week - brackets for NA and NB MX-5!

Passenger and drivers side available. Limited stocks though, so get in quick!

is my name on one of these passenger sets? :P

Rupewrecht
26-05-2012, 08:52 PM
Hey Rupe Keen on some Eunos Brackets, although last time I tried putting Aussie Delivered Eunos 30x seats in my car it didn't fit as the rail width was too wide to bolt into my floor , so not really sure which Brackets I'd need.

Weird, i have no explanation for that. I've had a few other sets of the BG/AZ-3 ones that have worked fine for other people. They're listed as the same for all BG FWD and AZ-3.

is my name on one of these passenger sets? :P

But of course :)

Born_Disturbed
11-06-2012, 05:19 AM
Ill take a set of passenger MX5 ones man :D

mcwilly
15-02-2014, 12:42 AM
Hey mate im keen for a set of brackets for a bg astina. Would these work with seats such as sparco recaro and bride aswell?

Rupewrecht
15-02-2014, 09:01 AM
Hey mate im keen for a set of brackets for a bg astina. Would these work with seats such as sparco recaro and bride aswell?

Only Mazdaspeed seats.

323c
16-01-2015, 11:54 PM
Hey Rupe,

Sent you a PM about Mazdaspeed Seat Brackets for BA.

Thanks.