FS: [AUS] Mazdaspeed Seat Brackets for BA, BG and NA/NB
Mazdaspeed seats will fit in any car, but the seats themselves have an integral rail that cannot be removed, unlike most aftermarket seats.
This means they require a set of adapter brackets that mount to the corner of the integral rail for each different car. These brackets are quite hard to find for most models, and are unavailable new from Mazda/Mazdaspeed for anything pre-2005. So, i'm looking at getting drivers and passenger brackets replicated for: - CBA Lantis / BA Astina / 323F - BG Astina / BG Familia + Protege 3DR Hatch and BG Sedan (not 4WD) / Eunos 30X / Mazda MX-3 / Mazda Presso / Autozam AZ-3 / Eunos 100 - NA/NB MX-5 / Miata / Eunos Roadster - No BJ ones at this stage, as i'd have to find them on the auctions and i don't think i've ever seen a set! This will give anyone looking at the seats a much easier time to fit them - it's just a few simple bolts. Projected cost is $85 per seat. Ideally, i'd need 5-10 firm orders of each to make it worthwhile, and to cushion some of the $800+ outlay for each type. But honestly, i'd be happy to sell a set of brackets with a seat for a decent amount less, just to sell a seat. Interest? |
Here's a pic of the bottom of a Mazdaspeed seat, showing the integral rail. I've had a good look at the rail and it's part of the seat - to remove it would make the seat collapse!
http://rupewrecht.com/forsale/fs_ms_...asurements.jpg |
After getting a couple of questions about this, these brackets bolt to the seat, and then bolt to the floor.
The large holes are the the ones that bolt to the floor, and the 2 set of small holes bolt to the studs on each corner of the rail on the Mazdaspeed seat base. There is no need for anything else to fit a Mazdaspeed seat to your car, apart from a set of these brackets. http://rupewrecht.com/forsale/fs_ms_...tbrackets3.jpg |
keen.
i'd also assume alot of mx5 boys would be also |
I've been directed here from MX5nutz, and I'd happily take a set of these!
|
im keen also as u already know :)
|
i take it these never eventuated at all?
|
They will, but when i have to find $1700 per car to get them made it's going to take a little while.
|
+1 BA Astina passenger bracket for me.
Got the Mazdaspeed Sport seat for the drivers side at the moment and need these brackets to put in the passenger side seat LOL. Pretty good seats compared to the standard series 3 ones. |
i will take 2 sets of bg ones please
|
Just a heads-up - both drivers and passenger seat brackets for BA Astina are being made in the next 2 weeks, so please indicate your interest to make sure you don't miss out! Limited stocks.
|
Quote:
|
Quote:
|
Now in stock:
Mazdaspeed seat brackets for: 1994-1998 323 BA Astina / CBA Lantis / BA 323F. 1994-1998 323 BH Protegé / BHA Familia / BA Protegé (2WD only) - Drivers side and Passenger side available. - Fits both Hatch/Coupé and Hardtop/Sedan. - Works with Mazdaspeed Type-F, Type-T and Sports seats. - Available in pairs (LHS and RHS) or individual sides. - 8 sets available only (and probably no more after this!). Price: - $110 per individual seat (LHS or RHS) - $210 for a pair (RHS and LHS) Shipping: - Australia: $15 for either a single or pair of brackets, Australia-wide. - International: Please PM for a quote. The brackets: http://rupewrecht.com/forsale/fs_ms_...ets_repro2.jpg http://rupewrecht.com/forsale/fs_ms_...ets_repro2.jpg |
Have you spotted a set on the auctions for BJ yet??
|
Quote:
|
that doesnt mean we cant make AGT ones :P
|
OK, prototypes are currently being made for NA/NB MX-5, thanks to Scott B / SJB Engineering :)
Both Drivers/RHS and LHS/Passenger brackets will be made. Please indicate your interest! Projected cost is around $98 per side, or $190 for a set of both sides. |
Hey rupe, i would need 2 out of the 4 NA P/S mounts as i have the other 2, also any chance of some BG 4WD mounts? fair bit of intrest this side of things if its possible
|
Quote:
As for BG, i've got a set of BG FWD ones that might be done one day, but i don't know if there's really demand for them. I've never seen any for BG 4WD, so they'd have to be mocked up/CADed and made - but it's possible. Would really need some firm interest for either of the BG ones though. |
All times are GMT +10. The time now is 07:09 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
2001- 2010 AstinaGT