FS: [VIC] massive performance parts clearout!!!

adenjr · 21-04-2011, 01:50 PM

garage clearout! need all this stuff gone asap!!

cheap parts, so dont hesitate, cos before you know it.. BAM!!! and theyll be gone.

MELBOURNE PICKUP ONLY!!! really dont have time to organise postage

im in the western suburbs 15mins from the city.. so feel free to come down and suss everything out.. backyard/garage looks halfway between a wrecking yard and autobarn at the moment..

engine setup incl.
-low km n/a import 95' GT astina block
-bored to 1.9L
-sump tapped for turbo oil feed lines
-big end crank [from GTR BPD]
-wiseco low comp .40 thou over pistons
-shotpeened B6T rods
-oil & water pumps
BP N/A head
BPT cams
schmick painted pulleys
stripped and wrinkle painted red rocker cover [honda type r vtec stylez yo]

corksport adjustable cam gears
[brand new in the box!!!]

custom intake plenum
[ss]

holden GENIII V8 throttle body
[like 75mm]

custom aluminium fuel rail w/ 2 -6AN fittings and 1 -4AN for fuel pressure guage

RX7 550cc injectors

malpassi rising rate fuel reg
[looks weathered but does the job]

bosch in-tank fuel pump

superpro rr lwr trailing arm bushes
SPF2744K
[brand new!!!]

4 LS1 coil packs with mounts

custom nissan CA18 tuned length spaghetti exhaust headers w/ fibreglass heat wrap & 3inch dump [ss]

gates racing [blue] timing belt
[brand new!!!]

bosch alternator
[brand new!!! you know how much a brand new alternator costs]

tensioner & idler bearings
[brand new!!!]

ARP head stud kit BP
[brand new!!!]

ARP main stud kit BP
[brand new!!!]

CORKSPORT j-spec gtr clutch slave cylinder
[brand new!!!]

WHITELINE CAMBER BOLT KIT set of 4
[used good condition]
*-/+ 2 degrees camber

WASP ball joint set
[new]

2 1/4 inch N/A exhaust that was on my KF BP, with twin polished dump tips
cat-back, incl hollowed out cat
[looks messy, but sounds tough, not too loud does the job]

TURBONETICS EVOLUTION external wastegate w/ stainless screamer
[good condition] rrp $350

TURBONETICS GODZILLA BOV
[needs new spring kit-cheap buy]
* massive! rrp $495

lightened balanced flywheel with Sach's single plate 7.25" race clutch (mazda disc)

chrome plated and detailed w/ blue striping power steering pump

Besides these performance parts also have..

G-SERIES standard gearbox
[200xxx kms perfect working order removed due to upgrade]

KE TX3 shell in ensign blue
[straight but needs respray]

KE TX3 bonnet w/ ford falcon GT bonnet buldge mould
[straight but needs respray]
*looks super tough

KE ONLINE fibreglass side skirts
[straight but needs respray]

KE FRONT STRUTS incl. KYB shocks & SUPERLOW KING SPRINGS
[good condition]

KE REAR STRUTS incl. BORGE shocks & SUPERLOW KING SPRINGS
[good condition]

KE FRONT HUB & BRAKE PACKAGE incl. Ford Telstar AS hubs [4x114.3], Mitsubishi Galant VR4 slotted rotors [26cm x 2.5cm], either BG GTX or Ford Telstar calipers
[working order but slotted rotors have heavy surface rust]

G-SERIES gbox modified w/ INFINI LSD, straight cut 3rd gear, Telstar long gearset w/ shorter 4th
[suits rebuild- still in working order however possible noisy 3rd and worn LSD]
*rare

LCD instrumental digital dash cluster from JAP Mazda 323 Super-Delux
[taco sometime doesnt come on may be due to dry joint on circuit board]
*rare

VIC [FLYIN-4] slimline blue & white numberplates
[vg condition]

AUTOTECHNICA black leather steering wheel w/ boss
[vg condition]

17" RJR circuit rims 4x114.3 w/ NANKANG ULTRA SPORTS NSII 205/40R
[set vg conditon tyres have 90% tread]

16" BA Mazda Astina V6 alloys 5x114.3 powder coated matte black w/ KUMHO ECSTA SPT 205/50ZR16
[set vg condition 75% tread]

TOYO PROXES RA1 205/50ZR15 semi-slicks on TX3 stockies
[pair 50% tread]
*track only!

Also..

random bits and pieces from BP mazda/ford KE KF and KH
ie.
-rocker covers
-n/a heads
-AFMs
-brakes
etc
etc

Djb · 03-07-2011, 11:06 PM

hey mate how much for the 17" rims and tires? and do threy suit BA Hatch?

Spykey · 13-08-2011, 06:29 PM

will this manifold fit a mazda sp20?

Clean_Cookie · 13-08-2011, 06:33 PM

the whole lots been sold afaik.

Spykey · 13-08-2011, 06:38 PM

means the intake

Ice88 · 13-08-2011, 08:46 PM

you mean the Intake manifold? No. Youd need an adapter plate made.

Oldno3 · 01-10-2016, 12:16 PM

Hi i was wondering if u have an ait flow meter for ke tx3 tutbo 1.6 b6t endine

21-04-2011, 01:50 PM	#1
adenjr Junior Member Join Date: Sep 2010 Location: Melbourne Car: 92' TX3 Posts: 12	FS: [VIC] massive performance parts clearout!!! garage clearout! need all this stuff gone asap!! cheap parts, so dont hesitate, cos before you know it.. BAM!!! and theyll be gone. MELBOURNE PICKUP ONLY!!! really dont have time to organise postage im in the western suburbs 15mins from the city.. so feel free to come down and suss everything out.. backyard/garage looks halfway between a wrecking yard and autobarn at the moment.. engine setup incl. -low km n/a import 95' GT astina block -bored to 1.9L -sump tapped for turbo oil feed lines -big end crank [from GTR BPD] -wiseco low comp .40 thou over pistons -shotpeened B6T rods -oil & water pumps BP N/A head BPT cams schmick painted pulleys stripped and wrinkle painted red rocker cover [honda type r vtec stylez yo] corksport adjustable cam gears [brand new in the box!!!] custom intake plenum [ss] holden GENIII V8 throttle body [like 75mm] custom aluminium fuel rail w/ 2 -6AN fittings and 1 -4AN for fuel pressure guage RX7 550cc injectors malpassi rising rate fuel reg [looks weathered but does the job] bosch in-tank fuel pump superpro rr lwr trailing arm bushes SPF2744K [brand new!!!] 4 LS1 coil packs with mounts custom nissan CA18 tuned length spaghetti exhaust headers w/ fibreglass heat wrap & 3inch dump [ss] gates racing [blue] timing belt [brand new!!!] bosch alternator [brand new!!! you know how much a brand new alternator costs] tensioner & idler bearings [brand new!!!] ARP head stud kit BP [brand new!!!] ARP main stud kit BP [brand new!!!] CORKSPORT j-spec gtr clutch slave cylinder [brand new!!!] WHITELINE CAMBER BOLT KIT set of 4 [used good condition] -/+ 2 degrees camber WASP ball joint set [new] 2 1/4 inch N/A exhaust that was on my KF BP, with twin polished dump tips cat-back, incl hollowed out cat [looks messy, but sounds tough, not too loud does the job] TURBONETICS EVOLUTION external wastegate w/ stainless screamer [good condition] rrp $350 TURBONETICS GODZILLA BOV [needs new spring kit-cheap buy] massive! rrp $495 lightened balanced flywheel with Sach's single plate 7.25" race clutch (mazda disc) chrome plated and detailed w/ blue striping power steering pump Besides these performance parts also have.. G-SERIES standard gearbox [200xxx kms perfect working order removed due to upgrade] KE TX3 shell in ensign blue [straight but needs respray] KE TX3 bonnet w/ ford falcon GT bonnet buldge mould [straight but needs respray] looks super tough KE ONLINE fibreglass side skirts [straight but needs respray] KE FRONT STRUTS incl. KYB shocks & SUPERLOW KING SPRINGS [good condition] KE REAR STRUTS incl. BORGE shocks & SUPERLOW KING SPRINGS [good condition] KE FRONT HUB & BRAKE PACKAGE incl. Ford Telstar AS hubs [4x114.3], Mitsubishi Galant VR4 slotted rotors [26cm x 2.5cm], either BG GTX or Ford Telstar calipers [working order but slotted rotors have heavy surface rust] G-SERIES gbox modified w/ INFINI LSD, straight cut 3rd gear, Telstar long gearset w/ shorter 4th [suits rebuild- still in working order however possible noisy 3rd and worn LSD] rare LCD instrumental digital dash cluster from JAP Mazda 323 Super-Delux [taco sometime doesnt come on may be due to dry joint on circuit board] rare VIC [FLYIN-4] slimline blue & white numberplates [vg condition] AUTOTECHNICA black leather steering wheel w/ boss [vg condition] 17" RJR circuit rims 4x114.3 w/ NANKANG ULTRA SPORTS NSII 205/40R [set vg conditon tyres have 90% tread] 16" BA Mazda Astina V6 alloys 5x114.3 powder coated matte black w/ KUMHO ECSTA SPT 205/50ZR16 [set vg condition 75% tread] TOYO PROXES RA1 205/50ZR15 semi-slicks on TX3 stockies [pair 50% tread] track only! Also.. random bits and pieces from BP mazda/ford KE KF and KH ie. -rocker covers -n/a heads -AFMs -brakes etc etc

13-08-2011, 06:33 PM	#4
Clean_Cookie obsessed-incomplete-broke Join Date: Oct 2008 Location: Brisbane Car: BA Hardtop/Hatch Posts: 5,441	the whole lots been sold afaik. __________________ Worklog

13-08-2011, 08:46 PM	#6
Ice88 Senior Member Join Date: Jun 2008 Location: Auchenflower, Brisbane Car: Blue SP20 Posts: 2,782	you mean the Intake manifold? No. Youd need an adapter plate made. __________________

01-10-2016, 12:16 PM	#7
Oldno3 Junior Member Join Date: Oct 2016 Location: Melbourne Car: Ke tx3 Posts: 1	Hey mate Hi i was wondering if u have an ait flow meter for ke tx3 tutbo 1.6 b6t endine

03-07-2011, 11:06 PM	#2
Djb Junior Member Join Date: Jul 2011 Location: Sydney, Aus Car: 97' BA Astina Hatch Posts: 1	hey mate how much for the 17" rims and tires? and do threy suit BA Hatch?

13-08-2011, 06:29 PM	#3
Spykey AstinaGT Regular Join Date: Apr 2009 Location: From Melbourne - In Sydney Now Car: Mazda 323 SP20 TURBO Posts: 331	will this manifold fit a mazda sp20?

13-08-2011, 06:38 PM	#5
Spykey AstinaGT Regular Join Date: Apr 2009 Location: From Melbourne - In Sydney Now Car: Mazda 323 SP20 TURBO Posts: 331	means the intake