|
13-03-2011, 09:11 AM | #5561 |
Senior Member
|
not to do with my car but my older brother took my KLRout last night while i was at work that me and my dad have been building up for this years enduro season
last thing left to do was mount the bigger front brake disc and caliper, and jetting the carb he rode it into a 40cm high rock and snapped the gear selecter shaft clean off, cracked the gearbox/engine housing and its now jammed in 4th looks like where up for a new engine and panels from what ive seen this morning thinking about bolting it back together tanking all the race parts off and cut my losses looks like i cant enter 80's class at APEX Milton this year where i was hoping to near the podium. looks like im pitting this year oh well |
13-03-2011, 04:01 PM | #5562 |
obsessed-incomplete-broke
Join Date: Oct 2008
Location: Brisbane
Car: BA Hardtop/Hatch
Posts: 5,441
|
how is that even possible???
on a happier note (perhaps not for the neighbours) i got my kart going finally... tied it down onto the stand and used a rope to start it around the tyre, new sparkplug and some carby cleaner and finally it went... took it for a slow trip round the block and ive never been on a kart before but it was scary, for the first time in my life i was driving something with WAY too much power to control! cant wait to get it onto the ute and out to a proper track where theres no cars, no cops and no kids to run into
__________________
Worklog |
13-03-2011, 04:02 PM | #5563 | |
Junior Member
Join Date: Jan 2011
Location: Ashhurst, NZ
Car: Mazda Astina 1990
Posts: 121
|
Quote:
__________________
Anythings Possible. if you want it to work make it work |
|
13-03-2011, 05:15 PM | #5564 |
Administrator
Join Date: Mar 2002
Location: melb.vic.au
Car: AZ-1, Astina Hardtop Turbo, BJ Protege, Beetle
Posts: 16,525
|
Things i learnt today
1. BJ, GW wagon and BG Sedan/3DR all share the same front strut mounting points - so strut braces are universal to them all. 2. A JDM BJI Sport20 gauge cluster will work perfectly in a BJII 1.8 Protege. 3. BJ clusters keep the odometer readings in the cluster. 4. BJ JDM clusters have a different chime warning sound to AUDM cars! 5. BJ Sport20s had traction control 6. The tiptronic readout on the cluster doesn't interface with the BJII autos...but it does light up LOL
__________________
jdmparts.rupewrecht.com Sourcing your not-quite-overnight parts from Japan WRECHT--|--SLOWTEGE--|--BEETLE--|--SUBSTITUTE--|--AZ-1 |
13-03-2011, 05:15 PM | #5565 | |
Senior Member
Join Date: Oct 2009
Location: NSW
Car: 1998 Toyota Supra 3.0L Twin Turbo
Posts: 1,413
|
Quote:
outrageous.... they're crazy fun! the power to weight ratios are so stupid that ive seen a drag race between a kart and a lambo where the kart wins hands down. the best fun is turning around... "oh dead end, i'll just turn the steering wheel and floor it and do an instant 180"
__________________
1996 Mazda 323 Astina BA Hatch 1.8L - No Longer Mine |
|
13-03-2011, 06:22 PM | #5566 | |
Senior Member
Join Date: Oct 2009
Location: Adelaide, Australia
Car: 07 Subaru Liberty GT Spec B tuned by STi
Posts: 912
|
Quote:
I take it you were interchanging clusters in a car? |
|
13-03-2011, 06:27 PM | #5567 |
Administrator
Join Date: Mar 2002
Location: melb.vic.au
Car: AZ-1, Astina Hardtop Turbo, BJ Protege, Beetle
Posts: 16,525
|
Yeah, i picked up a Sport20 one off the Yahoo Auctions for the missus' car and put it in today.
__________________
jdmparts.rupewrecht.com Sourcing your not-quite-overnight parts from Japan WRECHT--|--SLOWTEGE--|--BEETLE--|--SUBSTITUTE--|--AZ-1 |
14-03-2011, 01:28 AM | #5568 |
E74A
Join Date: Nov 2004
Location: Sydney
Car: SP20
Posts: 1,248
|
Brought and installed a turbo timer - ended up being faulty
|
14-03-2011, 10:41 AM | #5569 |
Senior Member
|
changed gear oil on the weekend... some idiot put locktite on the drain hole and filler plug. i had to heat it up with the blow torch and mangle up the bolts... will get them replaced later on.
also found out that the left rear disc rotor is warped which is causing an annoying whining noise whenever i drive and brake. so now im going to upgrade the rotors from NA Fronts - 235mm Rear - 231mm TO NB Front - 270mm Rear - 276mm now i just need the cash to buy the upgrade before track day that is coming up in a week :\ |
14-03-2011, 10:53 PM | #5570 |
Senior Member
Join Date: Jun 2008
Location: Auchenflower, Brisbane
Car: Blue SP20
Posts: 2,782
|
Just got back from picking up my new CAI. Thanks to ****n road works took like 3x as long as it took to get there ffs.
Took about 45 mins to go from Salsbury to Manly
__________________
Last edited by Ice88; 15-03-2011 at 02:14 AM. |
14-03-2011, 11:02 PM | #5571 | |
Senior Member
Join Date: Sep 2004
Location: n/a
Car: n/a
Posts: 10,929
|
Quote:
track day? |
|
15-03-2011, 01:59 PM | #5572 |
Senior Member
|
Replaced my coil to distributor lead. The car had a set of Top Gun or Eagle or something performance leads when I bought it, but the coil lead always had tape over the end that connected to the coil. When I removed it today the inside of the coil end connector was all corroded and green and the casing was half ripped off. Replaced it with a normal Bosch lead after cleaning out the inside of the coil as best as possible.
Also the factory original ground lead [battery to chassis] was still on the car and it looked pretty ragged and corroded. So I cleaned up all the points with sandpaper and put on a nice big 2ga lead. And finally, I bought a new distributor cap and rotor button that will go in on the weekend when I change the accessory belts and flush the hydraulic system. Being unemployed sure gives you plenty of time to fix up piddly little things on your car. Last edited by derb; 15-03-2011 at 02:04 PM. |
16-03-2011, 10:16 AM | #5573 |
Senior Member
|
so for the first time last night i experienced something odd. started up the car and 2 min later it died. EVERYTHING works except for when you put it on ignition there are no dash lights and the boost gauge light doesnt turn on. engine cranks over and everything but no fuel delivery and no accessory lights. not even the hand brake light comes on.
things that do come on are, dash lights (when turning on head light), head lights, radio on ignition, engine cranks over normally, just the usual stuff. ive checked all the fuses. im suspecting either a relay that im not sure of, a broken wire somewhere, an imobilizer that possibly could have been there previously (i only have a single key). and worse case is it could even be the ecu. i'll check out as much as i can by this weekend and if not im just gonna give it to a sparky. i had to tow it to my work last night. *sigh* chewy |
16-03-2011, 05:24 PM | #5574 |
Senior Member
|
Almost ready for my weekend 'major' service. Just waiting until payday tomorrow to grab a few bottles of Motul RBF600 brake fluid and a Haynes guide that's coming in via post. Then it's new belts, new dizzy parts and a hydraulic system flush. I'm excited! |
16-03-2011, 09:52 PM | #5575 |
Senior Member
|
alright 24 hrs later and a stripped interior it turns out that the fake apexi turbo timer from ebay burnt out. fixed it and its running YAY. now i have money for a brake upgrade
Last edited by chewyryce; 16-03-2011 at 11:06 PM. |
17-03-2011, 02:01 AM | #5576 |
SP20 Member!
|
Hooked up my fuel pressure sender unit. Found a really neat solution that uses the stock fuel rail and FPR, and doesn't require cutting any fuel lines. I will post details in my build log on the weekend
Also, I just about finished relocating my coil packs. Again piccies and a bit of a write-up will appear in my build log over the weekend While I'm waiting on the Bumper Sag Fix brackets, I might even get a chance to sort out the power folding mirrors Slowly clearing the backlog of projects
__________________
Exhaust: Autoexe headers; Custom midpipe; Racing Beat catback Engine: AWR mounts; Twiggy cams; Custom CAI; RR Racing UDP; Mishimoto rad EMS: Microtech LT-10; J&S Safeguard; Gearbox: MSP LSD; Fidanza flywheel; 5th gear Rims/Suspension: MX-5 rims; Tokico Illuminas; Eibach Pro-kit; Progress RSB; AutoExe STB Exterior: MSP front lip & rear spoiler; Matt V headlights; AutoExe grill; EDM tails Interior: JVC AVX-77; Autometer gauges; DaveBs; B&M shifter Projects to come: Engine rebuild |
17-03-2011, 12:09 PM | #5577 |
Senior Member
Join Date: Jun 2008
Location: Auchenflower, Brisbane
Car: Blue SP20
Posts: 2,782
|
Fitted Orions old CAI last night, went for a bit of a drive. Interesting noise to say the least. Feels a heap better fixed a few issues with engine stalling at take off, but that was prolly ecu reset. Most likely take a lil while for the ecu to learn and ajust to suit the mods. To some degree my low idles been fixed to, doesnt drop to under 400 revs. Stays about 600 now.
__________________
|
17-03-2011, 12:29 PM | #5578 | |
SP20 Member!
|
Quote:
Good to hear it is working out for you
__________________
Exhaust: Autoexe headers; Custom midpipe; Racing Beat catback Engine: AWR mounts; Twiggy cams; Custom CAI; RR Racing UDP; Mishimoto rad EMS: Microtech LT-10; J&S Safeguard; Gearbox: MSP LSD; Fidanza flywheel; 5th gear Rims/Suspension: MX-5 rims; Tokico Illuminas; Eibach Pro-kit; Progress RSB; AutoExe STB Exterior: MSP front lip & rear spoiler; Matt V headlights; AutoExe grill; EDM tails Interior: JVC AVX-77; Autometer gauges; DaveBs; B&M shifter Projects to come: Engine rebuild |
|
17-03-2011, 01:23 PM | #5579 |
Senior Member
Join Date: Jun 2008
Location: Auchenflower, Brisbane
Car: Blue SP20
Posts: 2,782
|
Yah got it off mat on monday night. Pod barely fits in the wheel well. Everytime you put the accelerator down you can here the induction whoosh as the throttle body opens, then its like bring on the noise.
__________________
|
17-03-2011, 01:39 PM | #5580 |
The Hairy Mod
Join Date: Sep 2005
Location: southside ya'll and North Side, Brissy
Car: MINI Cooper S 2003
Posts: 8,110
|
you might of had a slight air leak after the air flow meter...
__________________
For All your crash repair panels & lights, clear lights contact us at
PANEL HOUSE 45 RANDALL ST SLACKS CREEK QLD 4127 PHONE : 07 3808 8737 FAX : 07 3808 8735 |
|
|