|
21-02-2011, 09:48 PM | #21 |
Senior Member
|
Just gave it to my mate so he can prep it. Going to drop the car to him on Friday night so he can have it all done by Saturday night also might buy a door and strip it all so he can stray it. Donno yet.
|
21-02-2011, 10:01 PM | #22 |
Senior Member
Join Date: Jan 2011
Location: casula, N.S.W.
Car: bj sp20 hatchback red
Posts: 996
|
hay where did you get the nite shades from been looking for some but they either dont stock it or are sold out
|
21-02-2011, 10:11 PM | #23 |
Senior Member
|
My mate gave it to me. I donno where he got it from sorry man
|
21-02-2011, 11:01 PM | #24 |
Senior Member
Join Date: Jan 2011
Location: casula, N.S.W.
Car: bj sp20 hatchback red
Posts: 996
|
nah thats all good i think i might just go try order some =]=]
|
21-02-2011, 11:20 PM | #25 |
Moderator
Join Date: Oct 2005
Location: Ipswich, Queensland
Car: 2002 Mazda Astina SP20 2006 Mazda 6 GY Wagon
Posts: 9,769
|
Autobarn stock nightshades fyi
Lip looks good,how easy it to put on the bumper?
__________________
|
22-02-2011, 01:01 PM | #26 |
Senior Member
|
The side parts sit pritty snug to the sides of the bar. But the centre bit I'm abit confused as to how I'm gonna make it stick down. My mate suggested urathane or just screw it there
|
22-02-2011, 05:54 PM | #27 |
Moderator
Join Date: Oct 2005
Location: Ipswich, Queensland
Car: 2002 Mazda Astina SP20 2006 Mazda 6 GY Wagon
Posts: 9,769
|
I had a good look on Mazdas247, and most just double sided tape the crap out of the middle, and some screw where it comes near the fogs... I'll be sure to let ya know 2moro
__________________
|
22-02-2011, 06:15 PM | #28 |
Veni, vidi, vici
Join Date: Mar 2008
Location: Brisbane
Car: 1996 BA Hatch & 2005 RX8
Posts: 4,911
|
hi man the lip looks very sweeet and the car is sitting very nicely on the springs espec with those rimz
if your gonna go the double sided tape way, make sure you clean the underside of your lip properly, ie take all the overspray off and hit it with rubbing alcohol just a little so its spotless, as well as your bumper. this way the tape will actually stick if your gonna screw it in, predrill the holes before the paint goes on and when you screw it in later use a screwdriver, not a power one my BA was drilled in cus it was fiberglass, but on the rx8 i just left it there cus it was sitting "close enough" and polyeurethane is a little bit of a bitch |
22-02-2011, 06:43 PM | #29 |
Senior Member
|
Thanks guys. Loving the way it's looking. Ay Marc how far are those clips??
I may just get him to do the tape thing I'll talk to my mate. |
22-02-2011, 06:48 PM | #30 |
Moderator
Join Date: Oct 2005
Location: Ipswich, Queensland
Car: 2002 Mazda Astina SP20 2006 Mazda 6 GY Wagon
Posts: 9,769
|
When I know about the clips, you guys will too (there in transit to Aus apparently )
__________________
|
23-02-2011, 08:35 PM | #31 |
Senior Member
|
Got intake
|
23-02-2011, 08:45 PM | #32 |
Senior Member
Join Date: Sep 2004
Location: n/a
Car: n/a
Posts: 10,929
|
is it up-side-down?
|
23-02-2011, 09:16 PM | #33 |
Moderator
Join Date: Oct 2005
Location: Ipswich, Queensland
Car: 2002 Mazda Astina SP20 2006 Mazda 6 GY Wagon
Posts: 9,769
|
It is, the sensor should be at the bottom
__________________
|
23-02-2011, 09:37 PM | #34 |
Senior Member
|
Upside down is it?? Lol I didn't really know how it sat.
|
23-02-2011, 09:42 PM | #35 |
Moderator
Join Date: Oct 2005
Location: Ipswich, Queensland
Car: 2002 Mazda Astina SP20 2006 Mazda 6 GY Wagon
Posts: 9,769
|
its suppose to sit kinda flush with the radiator support:
__________________
|
23-02-2011, 09:54 PM | #36 |
Senior Member
|
Probaly is upside down than. But it looks like if I turn it around it will be back to front compared to yours.
|
23-02-2011, 09:57 PM | #37 |
Senior Member
Join Date: Jan 2011
Location: casula, N.S.W.
Car: bj sp20 hatchback red
Posts: 996
|
Where the intake from?
|
23-02-2011, 10:04 PM | #38 |
Senior Member
Join Date: Sep 2004
Location: n/a
Car: n/a
Posts: 10,929
|
Tokyo Japan
Last edited by project.r.racing; 23-02-2011 at 10:06 PM. |
23-02-2011, 10:25 PM | #39 |
Senior Member
|
All the way from jap land baby :P it's probably one of only a hand few in aus land.
|
23-02-2011, 10:27 PM | #40 |
Administrator
Join Date: Mar 2002
Location: melb.vic.au
Car: AZ-1, Astina Hardtop Turbo, BJ Protege, Beetle
Posts: 16,525
|
__________________
jdmparts.rupewrecht.com Sourcing your not-quite-overnight parts from Japan WRECHT--|--SLOWTEGE--|--BEETLE--|--SUBSTITUTE--|--AZ-1 |
|
|